Put the Exit-Burr Note on the Drawing Before Through Broaching a Bearing Hub
A bearing hub's keyway width passes inspection, but the assembly team later finds a slight raised lip at the exit face. The lip may catch a mating component or interfere with a surface that was expected to sit flat. The drawing specified the slot; it did not say which exit edge to inspect or what edge condition is acceptable.
Through broaching exit burr inspection starts before the cutting job. Mark the exit face, its intersection with the internal slot, and any nearby bearing seat or mating face on the manufacturing drawing. Assign a measurable edge condition and an inspection method through the responsible design and quality process. A generic note to “deburr as needed” leaves room for a well-intended operation that damages an adjacent functional surface.
Name the exit face in relation to the chosen cutting direction
A hub drawing usually identifies front and rear faces, but the machining setup may reverse the direction the tool travels. The process sheet must say which face becomes the exit for the selected through operation and which feature edges are controlled. Avoid assuming that a drawing's back face is always the cutting exit.
The entry and exit can have different edge conditions depending on tooling, material, support and process. A raised edge at the exit is a possibility, not a claim that every broached part will have the same burr. The quality question is whether any residual raised material violates the part's agreed edge or assembly requirement.
Record the hub's nearby mating surfaces on the same detail. Where a bearing, washer, spacer or housing face approaches the keyway opening, even a small raised edge may matter. The design owner decides which surfaces must be protected and what edge break, if any, is permitted; the machinist should not infer that answer from visual appearance.
Annotate the exit edge and the neighboring seat together
Figure 1 is an original illustrative section and inspection-photo request, not a technical drawing of an actual customer's bearing hub. A identifies the exit keyway edge and potential burr check. B identifies the adjacent mating or bearing-seat face whose function must remain intact. The left schematic has no dimensions; the right is a mock photo-frame request, not inspection evidence.
Figure 1. Original exit-edge detail and suggested photo request. Actual edge-break limits, contact surfaces and inspection criteria must come from the controlled drawing.
A drawing revision can place a leader at A specifying the accepted edge condition, with the referenced inspection zone extending only as far as the design owner approves. A separate leader at B can tell the supplier which neighboring face must not be nicked or altered during deburring. If the design permits a chamfer or radius, give its required limits and inspection method; avoid inventing a universal edge-break size.
Write an acceptance note that can be used on the shop floor
A useful edge requirement answers four questions. Which edge is it? What is the permitted condition? How will the inspector determine whether it complies? What nearby material must remain unaffected? When the drawing leaves one of those answers undefined, request design clarification rather than manufacturing to an assumed interpretation.
Example of an incomplete note
“Remove all burrs on completion.” This gives no exit-face identifier, defined limit or protection instruction for the adjacent bearing seat.
Example of a controlled note structure
“At the exit-side intersection of slot K1 and face F2, meet edge condition EC-1 per the approved drawing detail. Preserve adjacent functional surface S1. Verify by method Q-1. Record any inaccessible area.”
The identifiers EC-1, S1 and Q-1 are fictional placeholders to demonstrate how a released drawing would organize the requirement. They are not standards, actual tolerances or valid instructions without a design owner's completed definitions. The point is to make the decision location and approval record clear before quotation or manufacture.
Ask for photographs that support—not replace—inspection
A photo can help a remote engineering reviewer recognize the edge orientation, but it is poor evidence without a scale and consistent lighting. Ask for a wide context view showing the hub face and slot identifier, then a close-up of the specific exit edge. Both should identify the actual face, orientation, observation date and whether the image was taken before or after deburring.
The photo request shown in Figure 1 asks the inspector to keep both A and B within the evidence set. Where practical, use a controlled close-up angle or oblique light to reveal raised material. Record what the image cannot resolve. The drawing's approved gauge, visual criteria or measurement method—not the existence of a photograph—determines acceptance.
For example, a bright reflection in an image may be a tool mark rather than a raised burr. A photograph cannot reliably establish a specified micron-scale limit by itself. The inspector should use the approved method and record pass, fail or unable to verify, with the relevant location and any needed reinspection.
Separate deburring from redesigning the edge
A planned deburring operation should remove unacceptable raised material while preserving required geometry. Excessive hand dressing or a broad chamfer can alter a functional face, keyway fit or other feature. Therefore, the machining route and edge-finishing method need process review, while the permissible final edge belongs to the design owner.
Ask whether the exit edge can be reached without contacting the bearing seat. If access is restricted, the shop might propose a different support, edge-control technique or inspection sequence. Any method change affecting the finished profile requires review. The same applies if a burr is discovered only after the hub has been assembled with another component.
A controlled first-article or sample-part inspection can be valuable before a repeat lot, especially when the exit-edge note is new. It should compare the actual outcome against the released requirement and record exceptions; it is not proof of future performance without the ongoing process controls specified by the responsible parties.
Give the through-hole supplier a complete edge requirement
Broaching Technologies, LLC describes through keyway machining and related slotting capabilities from its Wisconsin operation. When requesting a quote for a bearing hub, supply the controlled drawing, material information, bore and feature geometry, proposed machining direction, exit-edge detail, protected mating surface and inspection expectations. Ask the provider to identify what it needs before selecting the process.
When considering through-hole broaching services, ask the supplier how it will identify the exit face, inspect raised material and preserve the adjacent seat. A service description alone does not establish the edge condition or acceptance method for this particular hub.
Close the edge question before the first shipment
The release package should show the accepted exit edge, protected neighboring surface, inspection view and result owner. If the finished hub is held for a raised lip, the report should identify exactly where and against which approved criterion. A precise edge note lets the machinist quote the necessary work and lets quality inspection evaluate the part without guessing what the designer wanted.
Comments